November 14, 2026
The first thing to do with any washer leak is to turn off the water. The shut-off valves sit on the wall behind the machine, and turning them off stops the leak at its source. Then unplug the machine, mop up the water, and look at where the water is: at the back points at the hoses, at the front points at the door seal or the detergent drawer, and underneath points at the pump or the tub seal. Where the water sits is the fastest clue to the cause.
A leak that appears only during the fill points at the fill hoses or the inlet valve. A leak that appears only during the drain points at the drain hose or the pump. A leak that appears on every cycle, from the first minute, points at a hose or a seal that is always under pressure. Note when the water appears before you call — the timing is the first thing a technician will ask, and it narrows the fault to one part in most cases.
Massachusetts homes give washer leaks two particular settings. In older houses in Salem, Gloucester, and North Adams, the washer often sits in a basement with a floor drain, so a small leak goes unnoticed until the damp has spread. In newer homes, the laundry is often on the second floor, where a leak runs through the ceiling below within minutes. Either way, the fix starts the same way: water off, floor dry, source found. The sections below work through the sources in order.
The hoses at the back
The fill hoses carry water from the wall valves to the back of the machine, and they are the most common source of a washer leak. Rubber hoses stiffen and crack with age, their washers harden, and a connection that was only slightly loose can weep for weeks before anyone notices dampness behind the machine. Pull the machine out and look at both hoses along their whole length, and at the connections at both ends. A hose that is bulging, cracked, or wet at the fitting needs replacing.
Replace rubber hoses with braided steel hoses, which last longer and resist bursting. Turn the water off, unscrew the old hoses, and fit the new ones hand-tight plus a quarter turn with pliers — overtightening cracks the fitting. Check the washers inside the hose ends as well: a hardened washer will leak even on a new hose. Hoses should be replaced every few years as a matter of routine, because a burst hose can release a large amount of water in minutes, and it usually happens while nobody is home.
The door seal on a front-load machine
On a front-load washer, the door seal is the grey rubber ring around the door opening, and it is the second most common source of a leak. The seal folds back on itself, and the fold traps water, lint, and small objects. Over time the rubber tears at the fold, or mould grows in the trapped water and eats into the rubber. A torn seal lets water run down the front of the machine on every wash, and the puddle appears at the front, right under the door.
Look at the seal with the door open, and run a finger around the fold. A tear is usually at the bottom, where the water sits, and it can be small — a split a few millimetres long is enough to leak. Small objects caught in the fold, like a coin or a bra wire, can also cut the seal over time, so check the fold for anything sharp. A torn seal needs replacing, and the replacement must match the model, because seals are shaped for the door. A technician can fit one in a single visit.
The drain pump and the tub seal
A leak from underneath the machine usually comes from the drain pump or the tub seal. The drain pump sits at the bottom of the machine, and its housing can crack, or the seal where the pump meets the tub can wear. A pump leak shows up during the drain, when the pump is running and the water is under pressure. A tub seal leak shows up on every cycle, because the seal sits below the water line whenever the drum has water in it.
The tub seal is the seal between the inner drum and the outer tub, and it wears with age and with use. When it fails, water seeps down around the transmission and appears underneath the machine, often with a small amount of grease or dark staining. A tub seal is a bigger repair than a hose or a door seal, because it means taking the drum out, and on an older machine it is the point where the repair-or-replace question comes up. The repair or replace guide on this site lays out how to weigh it.
The detergent drawer and too much detergent
A leak from the front top of the machine usually comes from the detergent drawer. The drawer slides out for loading, and the housing behind it can clog with dried detergent, so water backs up and runs down the front instead of into the drum. Pull the drawer out fully, rinse it under a hot tap, and clean the housing behind it with a brush. A drawer that is clean and still leaks may not be seating properly, or its housing may be cracked.
Too much detergent causes a different kind of leak: suds. Modern detergent is concentrated, and using more than the measured dose creates suds that fill the drum, climb out of the dispenser, and run down the front of the machine. The suds can also get into the pressure switch hose and confuse the machine about the water level, which makes the problem worse. Use the measured dose, and use high-efficiency detergent in a high-efficiency machine — ordinary detergent makes far more suds than the machine is built for.
Finding the leak: where the water sits
When the source is not obvious, dry the floor completely, put a dry towel under the machine, and run a short cycle while you watch. Check the towel every few minutes. Water at the back means the hoses or the inlet valve. Water at the front means the door seal or the detergent drawer. Water underneath means the pump or the tub seal. Water that appears only during the spin usually comes from the tub seal or from a hose that moves when the drum spins.
One more check: the drain hose. The drain hose runs from the pump to the standpipe, and if it has slipped out of the standpipe, or if the standpipe is blocked, water backs up and spills onto the floor during the drain. Make sure the hose is seated in the standpipe and that the standpipe is not blocked. If the laundry sink gurgles when the washer drains, the blockage is in the house drain rather than the machine, and that is a plumbing repair. The washer not draining guide covers the drain side of the same machine in detail.
Massachusetts homes: basements, cold snaps, and upper floors
A washer in a Massachusetts basement faces two risks. The first is the cold: a hose that runs through an unheated space can freeze and crack, and the crack only shows when the hose thaws. If a leak appears after a cold snap, check the hoses first, and feel them for stiffness or a split. The second is the floor drain: a basement floor drain hides a small leak for weeks, because the water runs away instead of pooling. Check behind the machine regularly, even when the floor looks dry.
A washer on the second floor is the opposite problem: there is nowhere for the water to hide, and a leak runs through the ceiling below within minutes. If the laundry is upstairs, fit a drain pan under the machine and make sure the pan has a drain to the outside or to a floor drain. A pan will not stop a leak, but it will catch a slow one and give you time to turn the water off before the ceiling below is damaged. The washer repair service page on this site explains what a repair visit covers, and the washing machine repair page covers the same faults on machines sold under that name.
Frequently asked questions
What should I do first when my washer leaks?
Turn off the water at the wall valves behind the machine, unplug it, and mop up the water. Then look at where the water is: at the back points at the hoses, at the front at the door seal or the drawer, and underneath at the pump or the tub seal.
Why does my washer leak only during the spin?
The tub seal or a hose that moves when the drum spins is the usual cause. A seal that only leaks under the movement and weight of a spin cycle has worn to the point where it needs replacing.
Can too much detergent cause a washer to leak?
Yes. Too much detergent creates suds that climb out of the dispenser and run down the front of the machine. Use the measured dose, and use high-efficiency detergent in a high-efficiency machine.
Why does my washer leak after a cold snap?
A hose that runs through an unheated space can freeze and crack, and the crack only shows when the hose thaws. Check the hoses for stiffness or a split, and replace any hose that has frozen.
Is a leaking washer worth repairing?
It depends on the source. A hose or a door seal is a modest repair on any machine. A tub seal on an older machine is a bigger job, and that is the point where most homeowners weigh repair against replacement.
More from the Blog
Appliance trouble at home?
Call now — describe the problem and get a straight answer about what happens next.