Appliance repair across Massachusetts(866) 383-1857  ·  10 cities
Call (866) 383-1857
Appliance repair blog · Massachusetts

Why Is My Washer Not Draining?

A washer that will not drain leaves standing water in the drum and clothes that come out soaking wet. The cause is usually one of four parts: the drain pump filter, the drain hose, the drain pump, or the lid switch. This guide works through them in order, from the checks you can do yourself to the faults that call for a repair visit.

November 10, 2026

A washer that will not drain leaves standing water in the drum and clothes that come out soaking wet. The cause is usually one of four parts: the drain pump filter, the drain hose, the drain pump, or the lid switch. This guide works through them in order, from the checks you can do yourself to the faults that call for a repair visit.

A washer drains in a simple sequence. At the end of the wash and rinse cycles, the control board tells the drain pump to run, the pump pushes water out through the drain hose, and the machine moves on to the spin. When any part of that sequence breaks down, the water stays where it is, and the machine often refuses to go further. On a front-load washer, the door stays locked while water sits in the drum, which is a safety feature rather than a new fault.

The order of the checks matters. Most washers that will not drain are stopped by something simple and visible — a filter full of lint and small objects, or a hose that has been pinched behind the machine. Checking those two things first takes a few minutes and solves a large share of the problem. The pump, the switch, and the control board come after, and those are the faults a repair visit is for.

Massachusetts winters add one more cause that shows up in homes where the washer sits in an unheated basement or a cold garage, from the Berkshires to the North Shore. A drain hose that runs through a cold space can freeze, and a frozen hose blocks the drain just as surely as a clog does. If the machine stopped draining during a cold snap and the hose feels stiff or cold to the touch, warmth — not parts — is the fix. The guide below starts with the filter and works outward from there.

What a washer does when it will not drain

The symptoms tell you where the blockage sits. A machine that hums when it should be draining, with no water moving at all, usually has a pump that is jammed or a hose that is blocked. A machine that stays silent at the drain stage may have a switch or control fault instead, because the pump is never being told to run. A machine that drains slowly, leaving the load wetter than usual, usually has a partial blockage — a filter that is half full, or a hose that is kinked rather than fully pinched.

The error code on the display, if the machine shows one, narrows it further. Most washers flash a drain error when the water level does not fall within a set time, and the code means the same thing on every brand: the water is not leaving. Write the code down before you switch the machine off, because it helps the technician, but do not let the code decide the diagnosis on its own — the same code can come from a blocked filter or a failed pump.

The drain pump filter: the first thing to check

The drain pump filter sits behind a small panel or flap at the bottom front of most front-load washers, and behind a lower panel on some top-load machines. It catches lint, hair, coins, buttons, and anything else that slips out of a pocket, and it is designed to be cleaned. When it fills up, water cannot reach the pump, and the machine stops draining. This is the single most common cause of a washer that will not drain, and the fix takes ten minutes.

To clean it, put a shallow tray and some towels on the floor in front of the machine, open the panel, and unscrew the filter slowly. Water will come out — that is normal, and it is why the tray is there. Pull the filter out, rinse it under a tap, and pick out anything caught in the housing behind it. A sock, a coin, or a hair tie in the housing will block the pump just as well as a full filter, so check the opening with a torch before you put the filter back.

The drain hose and the standpipe

The drain hose carries water from the pump to the standpipe or the laundry sink, and it fails in three ways: it kinks, it clogs, or it freezes. A kink happens when the machine is pushed back too far against the wall, or when the hose is bent sharply where it enters the standpipe. Pull the machine out a few inches and look at the hose along its whole length. A hose that is folded flat, or pressed tight against the wall, cannot carry water no matter how well the pump works.

A clogged hose is harder to see. Detergent residue, lint, and mineral deposits build up inside the hose over years, and the inside narrows until the flow slows to a trickle. Disconnect the hose from the standpipe, hold the end over a bucket, and run a drain cycle: if water comes out strongly at the pump end but barely at the standpipe end, the hose is the problem. A replacement hose is a small part, and a technician can fit one in a single visit.

The drain pump itself

When the filter and the hose are clear and the machine still will not drain, the pump is the next suspect. A pump can fail in two ways. It can jam: an object that got past the filter — a coin, a small screw, a piece of wire from an underwired garment — catches in the impeller and stops it turning. Or it can fail electrically: the motor burns out, or the wiring to it breaks, and the pump stays silent when it should run.

You can tell the two apart by sound. A jammed pump usually hums or buzzes when the machine reaches the drain stage, because the motor is trying to turn against the obstruction. A pump with a failed motor makes no sound at all. Either way, the pump is a part for a repair visit: it sits at the bottom of the machine, it holds water, and replacing it means opening the machine and testing the new pump under load.

The lid switch and the door lock

On a top-load washer, the lid switch must register the lid as closed before the drain and spin stages are allowed to run. A switch that has worn out, or slipped out of position, tells the control board the lid is open, and the machine waits. The test is simple: with the machine on a drain and spin cycle, press the lid down firmly and listen for a click. If the machine starts draining when you press, the switch is the fault.

On a front-load washer, the door lock plays the same role. If the lock does not engage, the machine will not start the drain and spin, and if the lock does not release, the door stays shut with water inside. A door that will not unlock after a failed drain is usually the machine protecting you from a washer leak, not a broken lock — drain the water first, through the filter drain hose if the machine has one, and the lock should release once the drum is empty.

When the machine drains slowly instead of not at all

A slow drain is a partial blockage, and it deserves the same checks in the same order. Start with the filter, then the hose, then the pump. A filter that is half full will let some water through and hold the rest back, which is why the load comes out wetter than usual rather than soaking. A hose that is kinked halfway will do the same. A pump with a worn impeller will drain a small load and struggle with a full one.

Slow draining also shows up when the standpipe itself is the problem. If the standpipe is blocked further down — in the household drain rather than the machine — water backs up into the machine and the drain cycle never finishes. If the laundry sink or a nearby drain gurgles when the washer drains, or if water rises in the sink, the blockage is in the house drain, and that is a plumbing repair rather than an appliance repair. A technician can confirm this in a minute by watching where the water goes.

Frequently asked questions

Why is my washer not draining all the way?

The filter is usually half full, the hose is kinked, or the pump impeller has worn down. Clean the filter first, then check the hose for a kink or a freeze, and have the pump tested if the drain is still slow.

Why does my washer hum but not drain?

A humming pump is usually jammed by an object caught in the impeller — a coin, a screw, or a piece of wire. Switch the machine off, clean the filter, and check the pump housing. If the hum continues, the pump needs a repair visit.

Can I drain a washer by hand?

Yes, through the small drain hose next to the filter on most front-load machines, or by bailing the drum and then cleaning the filter. Keep towels and a shallow tray ready, because the drum holds several litres of water.

Why will my washer not drain in winter?

In an unheated basement or garage, the drain hose can freeze, and a frozen hose blocks the drain completely. Warm the hose gently and let it thaw fully, then keep the hose in a heated space or insulate the cold run.

Should I call for repair if the filter was the problem?

No, if the machine drains normally after you clean the filter. Clean it every few months and check pockets before washing. Call if the machine stops draining again soon after, because the blockage may be further along in the hose or the pump.

More from the Blog

Appliance trouble at home?

Call now — describe the problem and get a straight answer about what happens next.

Call (866) 383-1857 →
Call (866) 383-1857