A dryer that tumbles without heat leaves clothes damp after a full cycle, and a dryer that will not start at all leaves a wet load sitting in the drum. Both faults have the same set of usual causes, and sorting them out means testing one part at a time. The heating element or gas burner makes the heat, the thermostat and thermal fuse control it, the belt and motor turn the drum, and the vent carries the hot, damp air out of the house. When any one of those stops working, the rest of the machine cannot do its job.
Massachusetts homes run dryers hard through the winter, when thick clothes and bedding need long cycles and the air coming in is cold and dry. Lint builds up in the vent over time, and a partly blocked vent makes the dryer work longer, run hotter, and wear out its heating parts faster. A burning smell from a dryer is never a small thing: it usually means lint near the heater, or a belt slipping and heating up against the drum.
This page explains the most common dryer faults: the dryer that will not heat, the drum that will not turn, and the machine that stops partway through a cycle.
Dryer Not Heating
A dryer that tumbles but does not heat has a heating-circuit fault, and the first part to test is usually the thermal fuse. The fuse is a safety device: it breaks the circuit when the dryer overheats, which is what happens when the vent is blocked and hot air cannot escape. A blown fuse is a symptom as much as a fault, so replacing the fuse without checking the vent means coming back when the new fuse blows again.
On a gas dryer, the heat comes from a burner rather than an element, and the parts are different: the igniter that lights the gas, the gas valve coils that open the valve, and the flame sensor that confirms the flame is lit. An igniter that glows without lighting the burner points at the coils; a burner that lights and goes out points at the flame sensor or gas supply.
Dryer Will Not Start or Will Not Spin
A dryer that will not start at all usually has a door switch that no longer registers the door closed, a broken belt that has tripped the belt switch, or a blown thermal fuse that has cut power to the whole machine. The door switch is tested first, because it moves every time the dryer is used and wears out soonest.
When the drum will not spin, the belt is the usual suspect. Belts stretch, fray, and snap, and a belt that has slipped off its pulley leaves the motor spinning freely while the drum sits still. The drum rollers and the idler pulley carry the drum and keep the belt tight; when their bearings wear out, the drum drags, squeals, and eventually stops turning. The technician opens the cabinet, checks belt and rollers, and tests the motor.
Electric Dryer and Gas Dryer Differences
Electric and gas dryers look the same from the front, but their heating systems are entirely different, and the diagnosis follows different paths. An electric dryer heats with a coiled element on a 240-volt supply, and a fault can sit in the element, the thermal fuse, the high-limit thermostat, or the supply itself, including a breaker tripped on one leg so the drum still turns but the heat never comes on.
A gas dryer heats with a burner fed by a gas line, and its faults are the igniter, the gas valve coils, the flame sensor, and the gas supply. A gas dryer that runs but does not heat may have a cracked igniter, which is a common failure and a straightforward replacement. Both types share the same drum, belt, motor, rollers, and vent, so a spin fault or a noise fault is diagnosed the same way on either type.
Dryer Vent and Lint Cleaning
The vent is the part of a dryer that most people never see, and it causes more dryer trouble than any single part inside the machine. Lint escapes the filter on every load and collects in the vent hose and the duct through the wall or the floor. As the layer thickens, air moves more slowly, clothes take longer to dry, the dryer runs hotter, and the thermal fuse is more likely to blow.
Cleaning the vent means disconnecting the hose, clearing the duct with a brush or compressed air, and checking that the outside vent flap opens freely and is not blocked by a nest or debris. A short, straight run of rigid metal duct dries clothes fastest and collects the least lint; a long run with bends needs cleaning more often. Clear the lint filter after every load, and wash a filter with a waxy coating from dryer sheets, because a coated filter blocks airflow just as surely as a blocked vent.
Timer and Dial Problems
A dryer timer that does not move, or a dial that turns without changing anything, usually has a fault in the timer motor or the control. The timer is a small motor that advances the dial through the cycle: when it fails, the dryer either runs without ever finishing or stops at the same point every time. On a dryer with electronic controls, the same symptom points at the control board, which may have stopped sending power to the timer circuit.
The technician tests the timer motor for power and movement, and checks the dial and the wiring behind it for a loose connection or a burnt contact. A timer that sticks on one setting is usually replaced rather than repaired, and a board fault is confirmed by testing the parts around it first — a timer that works when tested on its own points back at the board.
Common problems we fix
Dryer Belt Replacement
A dryer drum that stops turning while the motor runs is usually a broken belt. Replacing it means opening the drum and fitting the new belt around it.
How a provider finds the fault
A dryer fault is found by checking heat, air, and motion in that order. The provider tests whether the drum turns, whether air moves through the vent, and whether the element heats.
A dryer with a failed heating element, thermal fuse, or belt is a repair at almost any age — all three are wear parts, and replacing them is a short job.
Frequently asked questions
Why is my dryer not heating?
A blown thermal fuse, a broken heating element, a faulty thermostat, or a blocked vent are the usual causes on an electric dryer. On a gas dryer, the igniter or the gas valve coils are the likely faults.
Why does my dryer take so long to dry clothes?
A partly blocked vent is the most common cause. Lint in the duct slows the airflow, so the dryer needs more time and runs hotter to finish a load.
What causes a burning smell from a dryer?
Lint collected near the heater or a slipping belt are the usual causes. Stop the dryer, clean the lint filter, and have the vent and belt checked before using it again.
Why will my dryer not start?
A worn door switch, a broken belt, or a blown thermal fuse are the usual causes. The door switch is tested first because it wears out soonest.
Why is my dryer so noisy?
Worn drum rollers, a worn idler pulley, or a belt that is slipping all make noise. A thumping sound often means a roller has flattened; a squeal usually means a belt or pulley bearing.
Is a gas dryer different to repair than an electric dryer?
The heating parts are different: gas dryers use an igniter, gas valve coils, and a flame sensor, while electric dryers use a heating element and thermostats. The drum, belt, motor, and vent are the same on both.
Why does my dryer timer not move?
A failed timer motor or a faulty control board are the usual causes. The timer is tested with a meter, and a timer that sticks on one setting is usually replaced.
Call now — describe the problem
An independent local provider looks at the machine, tests it, and tells you the fault and the fix in plain words.