November 15, 2026
An ice maker works in a short cycle. Water flows through a line into the ice mold, the mold freezes the water, a heater loosens the cubes, and an ejector arm pushes them into the bin. A sensor arm tells the ice maker when the bin is full. When any part of that cycle breaks down, the ice stops — and the pattern of the failure tells you which part it is. No ice at all points at the water supply. Small or hollow cubes point at low water pressure. Ice that forms but never drops points at the mold or the ejector.
Start with the two checks that need no tools: the water supply and the freezer temperature. The water line can be kinked, frozen, or shut off, and the freezer must be cold enough for the mold to freeze — usually around zero degrees Fahrenheit. Both are common, both are easy to check, and both are worth ruling out before you call.
Massachusetts homes add their own wrinkles. A water line that runs through an unheated basement or a cold wall can freeze in January, and a fridge in a seasonal house in Harwich that sits unused for months can dry out at the filter and the valve. The sections below work through the causes in the order a technician would check them.
The water supply line
The water line runs from the household supply to the back of the fridge, and it fails in three ways: it kinks, it freezes, or it gets shut off. A line that is kinked where the fridge was pushed back against the wall cannot carry water, and the ice maker gets nothing. Pull the fridge out a few inches and look at the line along its whole length. A line that is folded flat, or pressed tight against the wall, needs straightening or replacing.
A frozen line is a winter fault. A water line that runs through an unheated basement, a cold wall, or a garage can freeze, and a frozen line blocks the water just as surely as a kink does. Feel the line for a cold, rigid section, and warm it gently with towels soaked in warm water. Never use a naked flame. Once the line thaws, the ice maker should start filling again — and the long-term fix is keeping the line in a heated space, or insulating the run through the cold area. Also check the shut-off valve where the line meets the household supply: a valve that was turned off during a repair and never turned back on is a common cause, and it takes seconds to check.
The filter and the fill valve
The water filter sits inside the fridge or at the back, and it catches sediment before the water reaches the ice maker. When it clogs, the water pressure to the ice maker drops, and the cubes come out small, hollow, or misshapen — or the mold does not fill at all. Replace the filter on the schedule in the manual, usually every six months, and use a filter that matches the model. A filter that is past its life will slow the water even when it looks clean from the outside.
The fill valve is the electric valve that opens to let water into the mold, and it can fail in two ways. It can stick shut, so no water reaches the mold at all, or it can stick open, so water keeps flowing and freezes in the line. A valve that sticks shut gives no ice. A valve that sticks open gives a line full of ice and a mold that overflows. Both are repair-visit parts, because the valve sits at the back of the machine and needs testing with a meter. If the cubes are small or hollow, the filter is the first suspect. If there is no water in the mold at all, the valve is.
The freezer temperature
The ice maker needs the freezer to be cold enough — around zero degrees Fahrenheit — for the water in the mold to freeze in a reasonable time. If the freezer is running warm, the water in the mold may never freeze, or it may freeze so slowly that the ice maker cannot keep up with demand. Check the freezer temperature with a thermometer left in the freezer overnight. If it reads well above zero, the freezer itself has a fault, and the ice maker is only the symptom.
A freezer that runs warm usually has one of the faults covered in the freezer guide on this site: frost blocking the airflow, a failed defrost part, or a worn door seal. Fix the freezer first, and the ice maker will usually start working again on its own. Do not turn the freezer colder to compensate — a freezer that is set too cold ices over faster, and the frost then blocks the airflow that the ice maker needs.
The ice mold and the ejector
The ice mold is the tray the water freezes in, and it can fail in two ways. The coating inside the mold can wear, so the cubes stick and the ejector cannot push them out. Or the mold heater can fail, so the cubes never loosen at all. The symptom is the same either way: ice forms in the mold but never drops into the bin, and the mold stays full while the bin stays empty.
The ejector arm is the part that pushes the cubes out, and it can jam on a cube that has frozen in the wrong place, or on a piece of food that has fallen into the mold. Open the ice maker and look at the mold: if a cube is sitting half out, or the arm is stuck mid-cycle, clear the obstruction by hand and let the cycle run again. Do not force the arm — it is driven by a small motor, and forcing it can strip the gears.
The dispenser and the bin
A dispenser that will not dispense ice is a different fault from an ice maker that will not make ice, and it is worth telling them apart before you call. If the bin is full and the dispenser gives nothing, the fault is in the dispenser: the auger that moves the ice, the motor that drives it, or the flap that opens to let the ice out. If the bin is empty, the fault is in the making, not the dispensing, and the earlier sections apply.
The sensor arm is the wire arm that tells the ice maker when the bin is full. If the arm is stuck in the up position, the ice maker thinks the bin is full and stops making ice, even when the bin is empty. Push the arm down gently and see if it moves freely. If it is bent or stuck, it needs adjusting or replacing, and that is a small repair. The ice maker repair service page on this site explains what a repair visit covers.
Massachusetts homes: cold rooms and seasonal houses
A fridge in a Massachusetts home often has its water line running through a space that was never meant for it: a basement that drops below freezing in January, a wall that faces the wind, or a garage that is unheated all winter. A line that freezes once will freeze again, and the fix is to move the line, insulate it, or keep the space heated. If the ice maker stops every winter and works every summer, the line is the cause, and no part inside the fridge will fix it.
A fridge in a seasonal house in Harwich or on Cape Ann has the opposite problem: months of standing still. The filter dries out, the valve sticks, and the first ice of the season comes out small or cloudy. Replace the filter at the start of the season, run the ice maker through a few cycles and throw the first batches away, and leave the water on while the house is empty only if the line is in a heated space. The refrigerator cooling guide covers the matching fault on the fridge side, and the refrigerator repair service page covers both machines together.
Frequently asked questions
Why is my ice maker not making ice at all?
The water line is kinked, frozen, or shut off, the filter is clogged, or the fill valve has stuck shut. Check the line and the valve first, then replace the filter, and call for a repair if the mold still gets no water.
Why are my ice cubes small or hollow?
The water pressure to the ice maker is low, usually because the filter is clogged or the water line is partly kinked. Replace the filter and straighten the line, and the cubes should come back to full size.
Why does my ice maker work sometimes and not others?
A freezer that runs warm, a sensor arm that sticks, or a fill valve that works when cool and fails when hot can all give an on-and-off pattern. Check the freezer temperature first, then the sensor arm.
Should I throw away the first ice after replacing the filter?
Yes. Run the ice maker through a few cycles and throw the first batches away, because the new filter can leave a taste in the first cubes. The ice after that should taste clean.
Can I fix an ice maker myself?
The line, the filter, and the sensor arm are homeowner checks. The fill valve, the mold, and the ejector motor are repair-visit parts, because they sit inside the assembly and need testing with a meter.
More from the Blog
Appliance trouble at home?
Call now — describe the problem and get a straight answer about what happens next.