November 19, 2026
An oven heats by bringing the cavity up to the set temperature and holding it there. On a gas oven, a burner does the heating, lit by an igniter. On an electric oven, a bake element at the bottom and a broil element at the top do the heating, switched on and off by a thermostat. When any part of that chain fails, the oven stays cold, heats slowly, or heats and then stops — and the pattern tells you which part it is.
Start with the two checks that need no tools: the settings and the visible element or igniter. A setting that was knocked, or a control that is waiting on a delay start, can leave the oven cold without any fault at all. An element with a visible break, or an igniter that glows but never lights the gas, tells you the part before you call. Both are easy to check, and both are worth ruling out first.
Massachusetts homes give ovens one particular setting: the holiday kitchen. An oven that has run lightly all year and then cooks for a crowd in November or December is the one that fails, because the fault was there all along and the heavy use is what shows it. The sections below work through the causes in the order a technician would check them.
Gas ovens: the igniter
The igniter is the part that lights the gas, and it is the most common cause of a gas oven that will not heat. The igniter glows white-hot to open the gas valve and light the burner, and over time it weakens until it glows but no longer gets hot enough to open the valve. The symptom is an oven that stays cold, with the igniter glowing orange inside, and no flame. The glow without a flame is the clue: the igniter is trying, and it is not strong enough.
Electric ovens: the bake and broil elements
On an electric oven, the bake element sits at the bottom and the broil element at the top, and either one can fail. A bake element that has broken will often show a visible gap, a blister, or a bright spot where the coil has thinned, and the oven will stay cold or heat very slowly. A broil element that has failed will leave the top of the oven cold, so food browns on the bottom and stays pale on top.
Look at both elements with the oven off and cool. A break is often visible as a gap in the coil, or a spot where the metal has blistered. If you can see the break, the element is the fault, and the fix is a new one. If the elements look fine and the oven still will not heat, the fault is further along — the thermostat, the sensor, or the control board — and those need testing with a meter. Do not touch an element that is hot, and do not switch the oven on to test an element you suspect is broken.
An element that has failed can also trip the breaker. If the oven stopped heating at the same time as a breaker tripped, check the breaker panel and reset it once. If it trips again, leave it off and call for a repair — a breaker that trips repeatedly is a fault, not a nuisance. The oven and range repair service page on this site explains what a repair visit covers.
The thermostat and the temperature sensor
The thermostat is the part that holds the oven at the set temperature, and the temperature sensor is the part that tells the thermostat what the temperature actually is. When the sensor fails, the oven can heat too much, too little, or not at all, because the thermostat is working from wrong information. The symptom is an oven that is always cold, always hot, or always off by the same amount — food that is always underdone, or always burnt, at the same setting.
Test the temperature with an oven thermometer, left in the middle of the oven for a full preheat cycle. If the thermometer reads well below the set temperature every time, the sensor or the thermostat is the fault. If the temperature swings widely — hot, then cold, then hot again — the thermostat is not holding, and it needs replacing. Both parts are tested with a meter, and both sit inside the oven behind panels, so this is a repair visit.
The control board
The control board is the part that runs the oven: it reads the sensor, switches the element or the igniter, and drives the display and the timer. When the board fails, the oven can do any of several things: stay cold with the display working, show an error code, or refuse to respond to the controls at all. A board that has failed often shows signs — a display that flickers, a relay that clicks repeatedly, or a code that comes back every time it is cleared.
A board fault is diagnosed by ruling out everything else first: the element, the igniter, the sensor, and the thermostat are all tested, and if they are all fine, the board is the fault. That is why a board is never the first part to suspect, and never the first part to replace. A board is also the most expensive part in the oven, and on an older machine it is the point where the repair-or-replace question comes up. For that decision, the repair or replace guide on this site lays out how to weigh the age of the machine against the cost of the part.
The gas supply and the power supply
On a gas oven, check the gas supply. If the cooktop burners light normally, the gas supply to the house is fine, and the fault is in the oven itself. If the cooktop burners do not light either, the gas supply is the problem, and that is a gas company call, not an appliance repair. If you smell gas near the oven, leave the room, do not switch anything on or off, and call the gas company from outside the house.
On an electric oven, check the power. An electric oven runs on two circuits, and if one of them has tripped, the oven may show a display and still not heat, because the element has no power. Check the breaker panel for a tripped breaker, and reset it once. If it trips again, leave it off and call for a repair. A gas oven needs only a standard outlet for its igniter and controls, so a power problem there is less likely, but the outlet itself is still worth checking. The cooktop repair service page covers the burners that share the gas supply with the oven.
Massachusetts homes: older kitchens and holiday cooking
Older kitchens in the ten cities this site covers — a Victorian in Salem, a mill-era house in North Adams, a cottage in Harwich — often have ovens that came with the house, or that were fitted when the kitchen was renovated years ago. An oven that has cooked lightly all year and then faces a holiday crowd is the one that fails, because the igniter or the element was already weak, and the heavy use is what shows it. If the oven has been slow to preheat for weeks, the fault was already there, and the holiday only made it obvious.
A cold kitchen makes it worse. An oven in an unheated space, or in a kitchen that drops cold overnight in a Massachusetts winter, takes longer to preheat, and a weak igniter or a tired element shows up sooner in the cold than in the warm. If the oven is slow every winter and fine every summer, the room is part of the story, and the part is still the fault. The dryer heating guide covers the matching heating fault on the laundry side, and the diagnosis is the same on both machines: find the part that makes the heat, test it, and replace it.
Frequently asked questions
Why does my oven glow but not heat?
On a gas oven, the igniter is glowing but no longer hot enough to open the gas valve. The glow without a flame is the clue. The igniter has weakened with age and needs replacing.
Why does my oven take so long to preheat?
A weak igniter, a failing bake element, or a thermostat that is reading wrong are the usual causes. Check the element for a visible break, and test the temperature with an oven thermometer.
Why does my oven heat and then go cold?
On a gas oven, the igniter works when cool and fails when hot. On an electric oven, a thermostat that fails as it warms up gives the same pattern. Both need a repair visit and a meter test.
Can I use my oven if the broil element is broken?
The bake element will still work, so the oven will heat, but food will not brown on top. A broken element should be replaced, because a damaged element can trip the breaker or damage the control board.
Is it safe to use an oven that will not heat?
It will not damage the food, but do not keep running a gas oven that glows without lighting — the gas valve may be opening without a flame. Turn the oven off and call for a repair visit.
More from the Blog
Appliance trouble at home?
Call now — describe the problem and get a straight answer about what happens next.